1, the chemical composition (%) C Si Mn manganese carbon Si P S P S Ni Cr Cu Ni Cr Cu ≤0.08 ≤1.00 3.0-5.00 ≤0.045 ≤0.03 ≤4.0-6.0 ≤16.0-18.0 ≤ 2.0-3.5 2, the general characteristics NTK D-10 is a low-nickel than SUS304, SUS304 higher than manganese, and copper-containing austenitic stainless steel. And SUS304 having substantially the same mechanical properties and corrosion resistance. 3, the scope of decorative tube / Housewares / Kitchen Supplies / Tableware 4, the product shape are available: coil / plate / strip 5, the physical characteristics (annealed state) elasticity N / m㎡ proportion 198.000 Kg / (mm .㎡) resistance (20 ℃) ??7.86 specific temperature μ ω.cm 77 specific heat (0-100 ℃) J / g. ℃ 0.5 Thermal conductivity (0-100 ℃) (0-500 ℃) W / cm. ℃ 0.12 0.17 intermediate thermal expansion coefficient (0-100 ℃) (0-500 ℃) X10 6 / ℃ 16.9 18.6 melting range ℃ 1400-14500 6, mechanical properties: Test conditions: room temperature after the indoor / 2B surface treatment / thickness 0.8mm anti Tensile Strength (N / mm2) endurance (N / mm2) stretchability% hardness (HV) is bent (R = t, 180deg) 645 321 51 175 7 no cracks, corrosion resistance: hole hole Fresh Fresh potential measurement result ( volts) NTK D-10 0.2 304 0.2 430 0.1 Determination Methods: JIS C0577 standards experimental conditions: 80 ℃ 1000ppm concentrations cl 8 ion solution, cold performance: Standard Test Results: (2B surface treatment / thickness of 0.8mm) NTK D-10 304 limit stamping ratio (LDR) 2.08 2.10 Erichsen value (mm) 13.2 13.2 Cornical cup value (mm) 37.6 38.0, stainless steel components can be divided Cr classification system (SUS400), Cr-Ni system (SUS300), Cr-Mn-Ni (SUS200) and precipitation hardening system (SUS600). 200 Series - chromium - nickel - manganese austenitic stainless steel 300 Series - chromium - nickel austenitic stainless steel 301 - scalability for molding products. Machine speed can also be hardened. Good weldability. Abrasion resistance and fatigue strength than 304 stainless steel. 302 304 with corrosion resistance, due to relatively high carbon intensity and therefore better. 303 - by adding a small amount of sulfur, phosphorus and make it more cutting processing. 304- namely 18/8 stainless steel. GB grades for 06Cr19Ni10. 309 - 304 - better temperature resistance. 316 - After 304, the second most widely used of steel, mainly used in the food industry and surgical equipment, add molybdenum to obtain a special corrosion-resistant structure. Than the 304 because it has better resistance to chloride corrosion and thus as "marine steel" to use. SS316 is often used to fuel recovery. 18/10 grade stainless steel is usually in line with the application level. [1] Model 321 in addition to the added titanium elements to reduce the risk of material other than the corrosion of the weld performance similar to 304. 400 Series - ferritic and martensitic stainless steel 408 - good heat resistance, low corrosion resistance, 11% Cr, 8% of Ni. 409 - the cheapest model (BAR), commonly used as automobile exhaust pipe, is a ferritic stainless steel (chrome steel). 410 - martensite (high strength chrome steel), good wear resistance, corrosion resistance is poor. 416 add sulfur to improve the processing performance of the material. 420 - "Cutting Class" martensitic steel, similar to Brandt's first high-chromium stainless steel this. Also used in surgical tools, can do very light. 430 ferritic stainless steel, decorative, such as for car accessories. Good shape, but heat resistance and corrosion resistance worse. 440 - high strength cutting tool steel, carbon slightly higher, after appropriate heat treatment to obtain a higher yield strength and hardness up to 58HRC, are among the most hard stainless steel. The most common application example is the "razor blades." There are three commonly used models: 440A, 440B, 440C, in addition to 440F (easy processing). 500 series - resistant chromium alloy steel. 600 Series - martensitic precipitation hardening stainless steel. 630 - The most common type of precipitation hardening stainless steel models, often called 17-4; 17% Cr, 4% Ni.